Overview

Cable Mat floor heating is installed safely & discretely in the cement screed under tile or any other floor finish. The heating systems high performance-low energy design offers an output of 60-100W/m² for living & bedrooms and 80-120W/m² for bathrooms.

Manufactured using only the finest materials, the tough AS/NZS compliant heating cable features a primary Fluoropolymer (Teflon) insulation layer around the heating conductor, a full earth screen and an outer PVC sheath.

In screed floor heating installations have traditionally involved complicated procedures and steel mesh to clip the heating cable onto. Heating cables supplied on a roll also require careful planning to ensure there are no hot or cold spots. The unique Cable Mat design removes the risk of uneven heat spots and the need for steel mesh and planning, since the heating cable is uniformly fixed to the underside of a fibreglass mat supplied with strips of adhesive tape for direct stick to the floor.

Cable Mat floor heating is available with both single or twin conductor heating cables terminating on 3m long cold tail leads and the ease of installation makes them an ideal ‘Do-it-Yourself” or Trade kit without requirements or experience for planning their layouts.

Features

• Available in kit form for trade or DIY install
• Waterproof - safe in wet areas
• Fully earthed and Teflon insulated floor heating element
• Maintenance free
• Energy efficient heating system
• Thermostatically controlled
• Allergy friendly - produces no VOC's (Volatile Organic Compounds)
• Healthy, produces no harmful EMR (Electro Magnetic Radiation)
• 10 Year warranty (including DIY & Trade supply)

Technical

Application: Direct & background heating for installation over concrete or F/C sheet floors. The mat is embedded in-screed directly beneath most hard floor finishes including tile, floating and timber floors.
Cable Mat Construction: Comprises of a flexible, robust fiber-glass mat with the looped heating element uniformly fixed on it. The heating element terminates to 3m length cold leads at both ends of the mat.
Heating Element: Self regulating twin or single heating conductor with Teflon insulation, protected by a metal earth shield with a second insulation sheath.
Voltage: 240 Volt AC
Output Power: From 150 to 200W/m²
Control: Programmable room or floor sensing (or a combination of both) control
Safety: IEC60335 compliant and wired into an earthed power supply connected through a RCD circuit. Safe in wet areas.
Quality: DIN EN ISO 9001:2000 standards
Approvals: SEMKO & UL certified
Cable Mat Warranty: 10 years

Installation

In Screed under tile, stone, timber and vinyl floors
Installation of Cable Mat is a simple process and offers a reduced installation time. After the subfloor has been prepared (cleaned and in some cases primed with a bonding agent), the cable mat is rolled out and stuck to the floor using the attached adhesive tape strips. The flooring can be immediately installed after the element fault monitor is connected to the cold tail leads.



Cable Mat is easily configured on-site to suit any floor layout

Trade Kits

Cable Mat floor heating kits are supplied complete for a succesful DIY & Trade install. Kits include:

• Cable Mat heater w/terminated cold tails
• Element fault monitor
• Digital programmable thermostat with built in timer & air sensor
• Floor probe sensor
• Installation guide
• Free design & layout service
• Telephonic technical & installation support
  

Bathroom Floor Heating Kits - 200W/m²



Room Heating Kits - 150W/m²

Downloads

   Cable Mat Installation Guide
          (in sand cement screed or self levelling screed for under tile, carpet & floating floors)

   Electrical Requirements for Electric Floor Heating

  Cable Mat Floor Heating Data Specification 
          (in sand cement screed or self levelling screed)

   AT8100V Programmable Thermostat Data Sheet
          (vertical mount, touch screen programmable thermostat)

   AT8100 Thermostat Operating Guide
          (horizontal mount, touch screen programmable thermostat)

   ETV1991 Thermostat Operating Guidelines
          (manual thermostat for DIN Rail mounting for connection to home automation system)